Skip to content
AB Contracting & Design LLC
Call

What it costs to remove a load-bearing wall in New Jersey

Angi's 2026 national average is $5,700, and most owners pay $1,400 to $10,000. A single-story house runs $1,200 to $3,000. A wall carrying a second floor runs $3,200 to $10,000. HomeAdvisor's June 2026 average is lower, at $3,000.

Those are market figures, not an AB quote. Below: each part of the job priced, what changes the number, the New Jersey permit and engineer rules, a worked Belleville permit fee, and our own prices for the patching after. Load-bearing walls and beams are part of our additions and structural work.

Published November 16, 2026 by AB Contracting & Design LLC, Belleville, NJ. N.J. HIC Reg. #13VH11431800. Market prices and New Jersey rules come from the sources linked below, read on the day of publishing.

Sunlit house interior stripped to its wood framing, with stud walls, open ceiling joists overhead and lumber on the subfloor
A house opened to its studs and ceiling joists. A stock photo, not an AB job. Photo: Brett Rogers, Pexels.

Three numbers to read side by side

Angi, national
$5,700 averageMost pay $1,400 to $10,000; the high end is $15,000 (Angi, October 2026).
HomeAdvisor, national
$3,000 averageFrom $500 to $15,000 (HomeAdvisor, June 2026). No page in the results gave New Jersey prices.
New Jersey carpenters
$34.61 an hourMean wage, May 2025: 10% above the national $31.55 (U.S. Bureau of Labor Statistics).

The two national averages differ by $2,700, so ask what each quote includes. Carpentry is the core of this work, and it costs more an hour here than nationally.

Load-bearing wall removal cost by house and wall

Angi's published ranges for each kind of job, with HomeAdvisor's beside them where it gives one. Both are 2026 national figures, not a quote from us.

Load-bearing wall removal cost by house and wall type, Angi and HomeAdvisor, 2026
The jobMarket range
Single-story houseThe wall holds up the roof or ceiling only. HomeAdvisor gives the same range.$1,200–$3,000
Two- or three-story houseThe wall holds up a floor and more above it. HomeAdvisor gives the same range.$3,200–$10,000
Interior wallOn average, by the wall material and what runs inside it.$1,200–$2,500
Exterior wallRarely done. Angi says it needs an engineer, an architect and a general contractor.Up to $10,000
Wall opened to a carport or patio$6,400 on average, in both Angi's and HomeAdvisor's guides.$3,200–$9,500
Wall replaced with a steel beamHomeAdvisor, by beam size and type. Angi averages $3,300 for a wall replaced with a beam.$1,300–$5,000

The story count matters most. A wall holding up a floor, its furniture and a roof needs a deeper beam, heavier posts and more temporary support than a wall under an attic.

Load-bearing wall removal cost, line by line

What each part of the job adds, from Angi's 2026 guide unless the note names another source. Each line is a market range, not our price.

Load-bearing wall removal cost by part of the job, 2026 market ranges
Part of the jobMarket range
Structural engineerSizes the beam and posts. HomeAdvisor puts the average visit at $500.$350–$800
Permit, national averageAngi's average is $1,700. Belleville charges far less; see the worked fee below.$500–$2,000
Beam, materialBy material: LVL $3 to $12 a foot, steel $6 to $20. A wall replaced with a beam averages $3,300.$3–$35 / linear ft
Demolition, drywall wallPlaster runs $0.45 to $0.75 and brick $2.90 to $6.40 a square foot.$0.30–$0.45 / sq ft
ElectricianTo move switches, outlets and wiring out of the wall.$50–$150 / hour
PlumberGas line moves run $15 to $25 a linear foot.$45–$200 / hour
Heating and cooling ductsWhen a duct runs up through the wall.$25–$55 / linear ft
Retexture ceiling or wallsPaint is $2 to $6 a square foot on top.$1.80–$3.80 / sq ft
General contractorShare of the project cost, the most common way contractors price this job.10%–20%

Hidden mold or asbestos can change the budget most. Angi puts mold remediation at $10 to $25 a square foot and asbestos removal at $5 to $20. In a house built before 1980, it says to have the wall inspected for both before demolition.

Interior wall with the drywall stripped off, leaving bare wood studs, with a window, a staircase and an old wooden door behind it
A wall opened to its studs: this is when wires, pipes and ducts show up. A stock photo, not an AB job. Photo: Monica Silvestre, Pexels.

What moves the price up or down

Five things decide where a wall lands in those ranges:

  • What sits on the wall. A roof alone, or a floor and a roof. That is the gap between Angi's single-story and multi-story ranges.
  • How wide the opening is. A longer span needs a deeper beam. Taller ceilings need taller beams too, Angi notes, which adds material and labor.
  • Flush or dropped beam. A dropped beam sits below the joists and stays visible. A flush beam is set up in the ceiling, with the joists cut and hung from it (This Old House). It takes more cutting and patching.
  • What runs inside the wall. Wires, pipes, gas and ducts each bring a trade, priced by the hour or the foot in the table above.
  • What carries the posts. The posts at each end of the beam sit over a beam or wall in the floor below. Where nothing is there, the support has to be built down to the foundation.

Older Essex County houses: what opening a wall finds

Most houses here are old. In Essex County the median home was built in 1958, and 29.1% date from 1939 or earlier (Census Bureau, ACS 2020–2024). In Belleville the median is 1951, and 32.4% are from 1939 or earlier (Census Reporter). That age shows up in the price:

  • Plaster and lath, not drywall. Plaster costs more to take down than drywall, and the patch has to meet old plaster on both sides.
  • Lead paint. 74.2% of Essex County homes were built before 1980. Paid work that disturbs paint in a home built before 1978 falls under EPA's lead rule: a certified firm, trained workers and lead-safe practices (EPA).
  • Old wiring. Wiring found inside an old wall may have to be replaced, not just moved, before the opening is closed up.
  • Ducts and pipes in the ceiling. Opening the ceiling for a flush beam can uncover runs that have to be rerouted around it.
Older house mid-renovation with the ceiling opened to its wood joists, a heating register hanging from a duct, wood lath on the walls and a painted brick chimney
An older house with the ceiling open: wood lath on the walls and a duct in the joists. A stock photo, not an AB job. Photo: Monica Silvestre, Pexels.

How the job runs, in order

  1. Confirm the wall carries load. A wall running across the joists is probably load-bearing, says This Old House's Tom Silva. So is one sitting on the main beam in the basement.
  2. Size the beam and posts. The engineer's drawing or calculation sets the beam, the posts and what carries them.
  3. Get the permit. In New Jersey it comes before the work, and the office has 20 business days to decide.
  4. Shore it up. Temporary walls go up on both sides to hold the joists while the old wall comes out.
  5. Take out the wall, then set the beam and posts. The posts land over bearing in the floor below.
  6. Get the framing inspected. The beam, posts and connections are checked before anything covers them.
  7. Patch the ceiling, walls and floor, then get the final inspection.
Gutted restaurant interior with exposed joists and temporary shoring during demolition at Abuelo's Steakhouse
Our job: temporary shoring holding up the joists during demolition at Abuelo's Steakhouse in Bloomfield.

Step 4 is the temporary shoring every load-bearing wall job needs. On the Abuelo's Steakhouse job in Bloomfield, the crew opened up the front wall and carried it on a new header beam, set with a material lift.

Carpenters setting a new header beam on a material lift across the opened storefront wall at Abuelo's Steakhouse
Our job: carpenters setting a new header beam on a material lift across the opened storefront wall at Abuelo's.

The New Jersey permit, and what it costs in Belleville

Removing a load-bearing wall is never permit-free work in New Jersey. The state code is plain about it:

  • Not ordinary maintenance. Ordinary maintenance never includes cutting away a loadbearing wall, or removing or cutting a structural beam or bearing support (N.J.A.C. 5:23-2.7(b)1 and 2).
  • Not minor work. Renovation in a one- or two-family home counts as minor work only when no primary structural members are altered (5:23-2.17A(c)1ii). So the work cannot start on notice.
  • 20 business days. The office has that long to approve or deny a complete application (5:23-2.16(a)).
  • Framing is inspected. The building mid-point inspection covers all structural framing and connections, and work cannot go on in a way that hides it first (5:23-2.18).

Belleville's fee, worked out

Alterations are charged on the estimated cost of the work. Belleville's building fee is $28 per $1,000, with an $85 minimum. Plan review is 25% of that fee, paid before the plans are reviewed (Belleville Code § 12-1.3). The state adds $1.90 per $1,000 (N.J.A.C. 5:23-4.19(b)). Our arithmetic at two job sizes:

Belleville building permit fee and state fee for a load-bearing wall removal, two example job costs
Estimated cost of the workBuilding feeState fee
$5,700, Angi's average$39.90 of it paid up front for plan review.$159.60$10.83
$10,000, the top of Angi's usual range$70.00 of it paid up front for plan review.$280.00$19.00

That is about a tenth of Angi's $1,700 national permit average. Moving switches, lights or outlets adds an electrical permit: in Belleville, $50 covers one to six of them, under the same code section. Our New Jersey permit guide compares Belleville's fees with Bloomfield's and the state's, and covers who files.

When New Jersey asks for an engineer

The construction official and subcode official may require adequate structural details, computations and other technical data. All engineering plans and computations carry the seal and signature of the engineer or architect responsible (N.J.A.C. 5:23-2.15(f)1vii). For a beam, that usually means:

  • An engineer's visit and beam calculation: $350 to $800 (Angi), $500 on average (HomeAdvisor).
  • A sealed letter or drawing naming the beam, the posts and what carries them down to the foundation.
  • The same drawing on site for the framing inspection.
  • One exception: a single-family homeowner who prepared the plans personally can have the seal waived, by affidavit (5:23-2.15(f)1ix).

Ask the construction office in your town what it wants with the application. Plan review cannot finish without it.

Our published prices for the finish work after

We have not published a price for taking out a wall. We do publish prices for the patching that follows it, so you can check that part of a quote line by line:

AB Contracting & Design published prices that apply to the finish work after a wall removal
Our published pricePrice
Drywall, hung and finishedPer 4 × 8 sheet, labor and material, spackled and sanded ready to prime. A minimum job size applies.$220 / sheet
Electrical fixture installLabor, per fixture.$300+ each
Vinyl or laminate floor installLabor; material extra.$5+ / sq ft

Read against a 12 ft wall taken out under an 8 ft ceiling, with a dropped beam, our arithmetic:

  • Drywall: the ceiling strip, the boxed beam and the two wall ends come to about 70 sq ft, or 3 sheets: $660 at our price.
  • Electrical: a switch and a light moved out of the wall, 2 fixtures at $300 and up: from $600.
  • Floor: the two old floors rarely match. Re-flooring the opened 12 × 24 ft room is 288 sq ft, or $1,440 in labor at $5.
  • None of these is a wall-removal quote. The engineer, beam, posts, shoring and permit are on top.

Our drywall cost guide works the sheet price out room by room. Every price we publish is on the price list.

Why published prices disagree

What the results Google showed for this search in Belleville said on November 16, 2026:

  • An Australian forum thread from 2015: "anywhere from $500 to $50000", in Australian dollars.
  • A Brooklyn renovation forum: a question about a townhouse wall, with no replies.
  • Kukun, first written in 2019: $1,500 to $3,000, engineer included.
  • A dumpster company's blog from 2024: $1,200 to $5,000 for a single-story house.
  • A handyman review site from 2023: $1,500 to $3,000 for a single-story house.
  • A Louisiana forum from 2019: $3,600 quoted for a 12 ft section, drywall, two outlets and the floor included.

None of them was a New Jersey page, and most leave out the engineer, the permit or the patching. Whichever bids you get, compare them on the same questions:

  • Is the engineer's letter or drawing in the price, and who hires the engineer?
  • Which beam: wood, LVL or steel, and what size? Flush or dropped?
  • Where do the posts land, and is any new support below them included?
  • Is temporary shoring on both sides of the wall in the number?
  • Who files the permit, and is the fee included?
  • Are the electrical, plumbing and duct moves priced, or extra?
  • Are the ceiling, wall and floor patches, paint and debris removal included?

Before you sign, you can also check a New Jersey contractor's registration.

Where we do structural work

From our office at 65 Newark Ave, Unit 1 in Belleville, across all 22 Essex County towns: Belleville, Bloomfield, Glen Ridge, East Orange, Nutley, Orange, Montclair, Newark, West Orange, Verona, Irvington, South Orange, Cedar Grove, Essex Fells, Maplewood, Caldwell, North Caldwell, Roseland, West Caldwell, Livingston, Millburn, Fairfield. We also work in Union and Passaic counties. Load-bearing walls and beams are part of our additions, framing and roofing work.

Every town we serve

Load-bearing wall removal cost questions

How much does it cost to remove a load-bearing wall in New Jersey?

Angi's 2026 national average is $5,700, and most owners pay $1,400 to $10,000. HomeAdvisor's June 2026 average is $3,000. No page in the results gave New Jersey prices. New Jersey carpenters earn 10% more an hour than the national mean. These are market figures, not an AB quote.

How much does a structural engineer cost to look at a load-bearing wall?

Angi puts a structural engineer at $350 to $800 for this job, and HomeAdvisor at $500 on average. In New Jersey, the construction official can require structural details and computations, sealed by the engineer or architect who designed them (N.J.A.C. 5:23-2.15(f)1vii).

Do I need a permit to remove a load-bearing wall in NJ?

Yes. Cutting away a load-bearing wall, or removing a beam or bearing support, is never ordinary maintenance (N.J.A.C. 5:23-2.7(b)). It is not minor work either, because a primary structural member is altered (5:23-2.17A(c)1ii). So the permit comes before the work. The construction office has 20 business days to approve or deny a complete application (5:23-2.16).

Do I need an engineer to remove a load-bearing wall in New Jersey?

Usually, yes. The construction official may require structural details and computations, and engineering plans carry the seal of the engineer or architect who prepared them (N.J.A.C. 5:23-2.15(f)1vii and ix). A single-family homeowner who drew the plans personally can have the seal waived by affidavit. The beam still has to carry the load.

How can I tell if a wall is load-bearing?

Look at the joists in the basement or attic. A wall running across the joists is probably load-bearing, and one running alongside them probably is not. Walls sitting on a beam or foundation wall in the basement, central walls and exterior walls usually carry load. An engineer or contractor confirms it before anything is cut.

How much does a beam cost to replace a load-bearing wall?

As material, an LVL beam is $3 to $12 a linear foot and a steel beam $6 to $20, in Angi's 2026 figures. Replacing the wall with a beam averages $3,300 there. HomeAdvisor puts the wall out and a steel beam in at $1,300 to $5,000.

Is it cheaper to remove a load-bearing wall in a one-story house?

Yes. Angi puts a single-story house at $1,200 to $3,000, and a two- or three-story house at $3,200 to $10,000. A wall holding up a floor and a roof needs a bigger beam, bigger posts and more shoring than one holding up a roof alone.

Can I remove a load-bearing wall myself in New Jersey?

The owner can apply for the permit (N.J.A.C. 5:23-2.15(d)), and the same plan review and inspections apply. HomeAdvisor says a professional should always size and install the beam. The wall has to be held up on both sides before it comes out, and the new beam and posts are inspected before they are covered.

What is the average cost of construction per square foot in New Jersey?

For new finished space, our published North Jersey average is $400 a square foot, labor and material. That is for an addition, not for opening a wall. Our home addition cost guide works it out by size.

Do you remove load-bearing walls?

Yes, with a properly sized beam, temporary shoring and a permit. We do structural openings in homes and commercial buildings. We have not published a price for it, which is why the totals on this page are market figures. Phone estimates are free; an in-person estimate is $50, and it comes off your contract when you sign.

Sources

  1. Angi, How Much Does It Cost to Remove a Load-Bearing Wall?

    National average and range, stories, interior and exterior walls, line items, beams, permits, engineer. Updated October 6, 2026.

  2. HomeAdvisor, How Much Does It Cost to Remove a Load-Bearing Wall?

    Average and range, wall replaced with a steel beam, structural engineer. Updated June 20, 2026.

  3. This Old House, How To Identify and Remove a Load-Bearing Wall

    Tom Silva on finding a bearing wall, temporary walls, posts, and flush or dropped beams. Updated May 2026.

  4. N.J.A.C. 5:23-2.7, ordinary maintenance

    Subsection (b)1 and 2: bearing walls, beams and bearing supports are never ordinary maintenance.

  5. N.J.A.C. 5:23-2.17A, minor work

    Subsection (c)1ii: minor work only when no primary structural members are altered.

  6. N.J.A.C. 5:23-2.15, permit applications

    Who may apply (d); structural details, computations and seals (f)1vii and ix.

  7. N.J.A.C. 5:23-2.16, permit procedure

    Subsection (a): 20 business days to approve or deny.

  8. N.J.A.C. 5:23-2.18, inspections

    Mid-point inspection of structural framing and connections; work may not hide an inspection.

  9. N.J.A.C. 5:23-4.19, state training fee

    Subsection (b): $1.90 per $1,000 of construction value.

  10. Township of Belleville Code, Chapter 12, § 12-1.3 Fees

    Alteration fee per $1,000, the $85 minimum and 25% plan review, as amended October 28, 2025; electrical fee of $50 for one to six outlets.

  11. U.S. Census Bureau, ACS 2020–2024, year structure built, Essex County

    Table B25034, with the median year in table B25035. Belleville from Census Reporter.

  12. U.S. EPA, Renovation, Repair and Painting Program

    Certified firms and lead-safe practices for paid work disturbing paint in homes built before 1978.

  13. U.S. Bureau of Labor Statistics, OEWS: carpenters, New Jersey

    Mean hourly wage $34.61, May 2025. The national series shows $31.55.

Want a number for your wall?

Call to talk the job through with Andrew, or send the details and Andrew will get back to you. An in-person estimate is $50, and it comes off your contract when you sign.