Skip to content
AB Contracting & Design LLC
Call

Heated bathroom floors in New Jersey: cost to install, cost to run on PSE&G, and the wiring

  • Install: about $878 to $1,278 for a 36 sq ft heated area, on top of the tile work. That is the mat, a floor thermostat and the electrician's hookup.
  • Run: 13.7¢ an hour at full power, at PSE&G's winter rate of 25.3¢ per kWh. Three hours a day is at most $12.31 a month.
  • Wiring: a 15 or 20 amp, 120 volt circuit with Class A GFCI protection, a floor sensing thermostat, and an electrical permit.

Published November 9, 2026 by AB Contracting & Design LLC, Belleville, NJ. N.J. HIC Reg. #13VH11431800. Prices, rates and rules come from PSE&G's tariff, New Jersey's construction code, three manufacturers' manuals and the Census Bureau, all linked at the end and read that day.

An older bathroom with cream wall tile, a built-in tub, a wall-hung sink and a red and white mosaic tile floor
An older tiled bathroom. A heating mat goes under new floor tile, so the time to add one is when the old floor comes up. A stock photo from France, not an AB job. Photo: Alf van Beem, Wikimedia Commons, CC0.

What a heated bathroom floor costs to install

An electric heated floor is a thin cable, either pre-looped on a mesh mat or clipped into a membrane. It sits in the thinset under the tile. A floor sensor and a wall thermostat switch it on and off. Here is what each piece costs for a heated area of 36 sq ft, about the open floor of a 60 sq ft bathroom once the tub, vanity and toilet are left out.

Cost of each part of an electric heated bathroom floor, 36 sq ft heated area
PartPriceSource
Heating mat, 120 V, 36 sq ft$519WarmlyYours TempZone roll
Floor thermostat with built-in GFCI$159 to $259WarmlyYours price list
Electrician: circuit, thermostat box, hookup$200 to $500WarmlyYours, national range
Heated floor, total$878 to $1,278Sum of the three rows
Tile labor over it, per sq ft$10 to $20+Our tile price

The tile line is there in any bathroom remodel, heated or not. So the heated floor itself adds roughly $878 to $1,278. Mat and thermostat prices are WarmlyYours' own list prices on November 9, 2026. The electrician's range is WarmlyYours' national figure. It says the price depends on local rates, wall access and whether a new dedicated circuit is needed.

Not in that total, and priced house by house:

  • Panel work, if the electrical panel has no open space for one more breaker.
  • Subfloor repair or new underlayment, when the old floor fails the manufacturer's rules (below).
  • Insulation under the floor, when the bathroom sits over a cold basement, crawlspace or garage.
  • Your town's electrical permit fee. Each New Jersey town sets its own.

Manufacturers build these systems to different outputs. That changes both the price and the bill:

An electric floor heating mat unrolled on a tile floor: a red heating cable in loops on clear mesh, with its black power lead coiled beside it
An electric heating mat, unrolled before installation. The red cable heats; the black power lead does not, and it runs to the thermostat. A stock photo, not an AB job. Photo: Hundehalter, Wikimedia Commons, CC0.

What it costs to run on a PSE&G bill

National guides price the electricity at 16¢ per kWh. WarmlyYours' 2026 cost guide uses that figure. Belleville and the rest of this part of Essex County are PSE&G territory, and PSE&G's tariff gives a higher number. For a household on PSE&G's standard residential rate and default supply, from October through May, each kWh costs:

  • Distribution: 4.87¢.
  • Supply (energy and capacity): 12.91¢.
  • Transmission: 6.88¢.
  • State program charges and credits: 0.66¢ net.
  • Total: 25.3¢ per kWh, sales tax included. That is 58% above the 16¢ national figure.

Here is what that means for a 540 watt floor, the 36 sq ft mat priced above. The figures assume the mat runs at full power the whole time. The floor sensor switches it off once the tile reaches its setting, so a real bill is at or below these.

Running cost of a 540 watt heated bathroom floor at PSE&G rates and a national rate
RatePer hour3 h a day, 30 days
PSE&G standard, Oct–May25.3¢ per kWh13.7¢$12.31
National guide, 16¢16.0¢ per kWh8.6¢$7.78
PSE&G time-of-use, off-peak (midnight–6 am)10.2¢ per kWh5.5¢$4.96
PSE&G time-of-use, mid-peak26.0¢ per kWh14.0¢$12.64
PSE&G time-of-use, on-peak (4–9 pm weekdays)38.3¢ per kWh20.7¢Weekday evenings only
  • A whole season: November 1 to March 31 at three hours a day is at most 245 kWh, or $61.95 at the standard winter rate.
  • On a time-of-use plan, set the schedule. A floor warming during the 4 to 9 pm weekday window pays 38.3¢ per kWh. The same floor before 6 am pays 10.2¢.
  • Using a third-party supplier? Swap your supplier's price in for PSE&G's 19.8¢ of supply and transmission.
  • It lands on the electric bill, not the gas bill. 73% of Belleville homes heat with utility gas and 14% with electricity, per the Census Bureau. The floor is an electric add-on either way.

What the electrical side needs

Since August 17, 2026, New Jersey's electrical subcode is the 2023 National Electrical Code (N.J.A.C. 5:23-3.16, DCA). Permit applications filed complete by February 17, 2027 may still be reviewed under the previous code (DCA, Fall 2026). The Code has required ground-fault protection for electrically heated bathroom floors since its 1999 edition (IAEI Magazine). Here is what the three manufacturers' manuals ask for:

  1. A circuit sized to the mat. A 36 sq ft, 120 V roll draws 4.5 amps. SunTouch's table: up to 12 amps on a 15 or 20 amp breaker with 14 AWG wire; up to 15 amps on a 20 amp breaker with 12 AWG. Over 15 amps takes a second circuit or a relay.
  2. Its own circuit, or a careful share. Schluter recommends a dedicated circuit, or one feeding only fixed room heaters, loaded to no more than 80% of the breaker. SunTouch allows an existing circuit with room for the mat plus a hair dryer, but not one with lights, motors or exhaust fans.
  3. Class A GFCI protection on every circuit. Schluter calls for a Class A (5 mA) ground fault circuit interrupter on each circuit. The Schluter, SunTouch and WarmlyYours floor thermostats have one built in, so a GFCI breaker is not needed with them.
  4. A floor-sensing thermostat in a deep box. Each heating system needs its own thermostat or power module and a floor sensor. SunTouch specifies an extra-deep box, at least 4 feet from the shower opening.
  5. Three resistance tests. SunTouch and WarmlyYours both log the cable's resistance out of the box, once it is fastened down, and after the floor covering goes on. A failed reading after tile means lifting tile.
  6. An electrical permit, filed by a licensed electrician. A new circuit is not on the ordinary electrical maintenance list in N.J.A.C. 5:23-2.7, so it needs a permit. If it counts as minor work, work may start on notice to the town, with the application within five business days (5:23-2.17A). Only a licensed electrician, or a single-family homeowner on their own house, may do the wiring (5:23-2.15).

One Belleville detail on that last rule: 20% of the town's homes are in two-unit buildings (Census Bureau). The do-it-yourself exception in N.J.A.C. 5:23-2.15 covers a single-family homeowner only. In a two-family house, the wiring goes to a licensed electrician.

Older Belleville houses: the panel, the subfloor and the cold underneath

Belleville's median home was built in 1951. 48% of its homes date from before 1950, and 32% from 1939 or earlier (Census Bureau, ACS 2024). Three things decide whether a heated floor in a house that age is a simple add-on or a bigger job.

1. The electrical panel

The mat needs a breaker of its own, or a circuit with spare room under the rules above. A panel with an open space makes it a short job. A full panel means the electrician has to make room first, and that is a separate line on the quote. Ask the electrician to look at the panel before the tile is chosen, not after.

2. The subfloor

Tile over a heating cable is only as good as the wood under it. Schluter's handbook sets the minimums for its DITRA-HEAT system:

  • Joists 16 inches apart: one layer of plywood or OSB at least 19/32" (5/8" nominal), tongue and groove.
  • Joists 19.2 inches apart: at least 23/32" plywood or OSB.
  • A board (plank) subfloor: planks at least 3/4" thick plus plywood or OSB underlayment at least 15/32", joists no more than 24 inches apart.
  • Lauan plywood and particle board underlayment cannot sit directly under the membrane. They come out or get replaced with plywood or OSB.

Opening the floor is when you find out which one you have. The fix is new underlayment, and it is far cheaper before tile than after.

3. What is under the bathroom

Heat goes down as well as up. SunTouch's manual says insulation is required for best performance. On a well-insulated wood subfloor, it says most floors can be heated up to 20°F warmer than they would otherwise be. A bathroom over an unheated basement, crawlspace or garage loses much of that through the floor. Sealing and insulating that space is the same building work our frozen pipes guide walks through for the pipes below a cold floor.

Red hot-water floor heating tubes laid in loops over silver insulation boards covering a whole room's floor
Insulation boards under a whole-room floor heating system. This one is hot-water tubing, the other kind of radiant floor; a bathroom mat sits on the subfloor the same way. A stock photo, not an AB job. Photo: Kiwiev, Wikimedia Commons, CC0.

How a heated floor fits a bathroom remodel

A heated floor goes in only when the bathroom floor is open, so the decision belongs to the remodel. The order, from the manuals:

  1. Decide where the heat goes during design. No mat under cabinets or built-ins with no floor clearance (SunTouch). Keep the cable 4 to 6 inches from walls, tubs and drains, and 6 inches from the toilet's wax ring. WarmlyYours' example heats 38 sq ft of a 60 sq ft bathroom.
  2. Demolition down to the subfloor. Then the subfloor gets checked against the rules above, and any underlayment fix happens now.
  3. Electrical rough-in. The new circuit and the thermostat box go in with the rest of the bathroom wiring, and get inspected before the walls close when a permit was pulled.
  4. Cable or mat, then the floor sensor. Tested for resistance before and after it is fastened down.
  5. Thinset or self-leveler, then tile. The cable is fully embedded. A final resistance test follows.
  6. Wait before turning it up. SunTouch says never put the system into full operation until the cement materials are fully cured, typically two to four weeks.

That is why the heated floor belongs in the bathroom plan from the first visit. Our bathroom remodeling page shows how we run a remodel from demolition to tile, with plumbing and electrical on the same schedule. Our bathroom remodels start at $12,000 with material. The bathroom remodel cost guide breaks that down line by line.

Heated bathroom floor questions

Is it expensive to heat a bathroom floor in New Jersey?

Less than most people expect, more than national calculators say. A 36 sq ft mat draws 540 watts. At PSE&G's October-to-May residential rate of 25.3¢ per kWh, that is 13.7¢ an hour at full power, or at most $12.31 for a month at three hours a day. National guides use 16¢ per kWh; PSE&G's winter rate is 58% higher than that.

Is heated flooring expensive to run all winter?

At three hours a day from November 1 to March 31, the same 540-watt floor uses at most 245 kWh, about $61.95 at PSE&G's winter rate. The floor sensor switches the mat off once the tile reaches its setting, so the real figure is lower. Leaving it on all day is what makes it expensive.

How long do heated floors last?

The cable is built to outlast the tile it sits under. SunTouch warrants its mats and cables for 25 years from the date of manufacture, and its thermostats for 3 years. The cable is buried in thinset under tile, so a damaged one means lifting tile. That is why every manual we read has the installer test the cable's resistance before, during and after the tile goes down.

Can you have a heated floor in a shower?

Some systems allow it, with rules. SunTouch's TapeMat is listed as suitable for a shower area, but its factory splice must sit at least one foot outside the shower. Schluter's handbook also keeps the factory splice out of the shower. Neither mat ever goes up the shower walls. The thermostat itself must be at least 4 feet from the shower opening, per SunTouch.

Does a heated bathroom floor need its own circuit?

Usually. Schluter recommends a dedicated circuit, or one that feeds only fixed room heaters, kept under 80% of the breaker. SunTouch says you may tap an existing circuit with room for the mat plus a hair dryer, but not one with lights, motors or exhaust fans. Either way the circuit needs Class A GFCI protection, which the floor thermostats in all three manuals have built in.

Do I need a permit for a heated floor in New Jersey?

Yes, for the wiring. A new circuit is not on the state's list of ordinary electrical maintenance in N.J.A.C. 5:23-2.7, so it needs an electrical permit. If your town treats it as minor work, the electrician can start once the town is notified and files the application within five business days. Electrical work must be done by a licensed electrician, unless you own a single-family house and do it yourself.

Can a heated floor be the only heat in a bathroom?

Sometimes. Schluter's handbook says it can in some cases, but that it depends on heat loss through walls, windows and doors, room size and how much floor is heated. It recommends an HVAC professional run a heating load calculation. In an older Essex County house with a cold exterior wall, plan on it as comfort heat on top of the existing system.

Sources

All read on November 9, 2026.

  1. PSE&G, Tariff for Electric Service, B.P.U.N.J. No. 17 (changes effective October 1, 2026)

    Rate Schedule RS distribution charges, BGS-RSCP energy, capacity and transmission charges, the per-kWh riders, the time-of-use periods, and the territory list naming Belleville. All figures include New Jersey sales tax.

  2. New Jersey Department of Community Affairs, Current Construction Codes

    Electrical subcode, N.J.A.C. 5:23-3.16: National Electrical Code (NFPA 70) 2023, adopted August 17, 2026.

  3. DCA, Construction Code Communicator, Fall 2026

    The 2023 NFPA 70 adoption and the grace period: last day to apply under the previous codes, February 17, 2027.

  4. N.J.A.C. 5:23-2, Administration and Enforcement (New Jersey Uniform Construction Code)

    Sections 2.7 (ordinary electrical maintenance), 2.14 (when a permit is required), 2.15 (licensed trades and the single-family homeowner exception) and 2.17A (minor work: notice first, application within five business days).

  5. IAEI Magazine, The History of GFCI Protection in the NEC (Summer 2024)

    Electrically heated floors in bathrooms added to the GFCI locations in the 1999 NEC; kitchens added later.

  6. Schluter-Systems, DITRA-HEAT Installation Handbook (10/2025)

    Watts per sq ft and amps by cable, dedicated circuit and 80% rule, Class A GFCI, subfloor minimums by joist spacing, plank subfloors, unacceptable underlayments, splice out of the shower, space-heating guidance.

  7. SunTouch (Watts), TapeMat Installation Manual, Series D12, C12 and C15

    12 and 15 watts per sq ft, breaker and wire table, sharing a circuit, GFCI in the thermostat, thermostat 4 feet from the shower, spacing from walls and the toilet, three resistance tests, insulation, cure time, 25-year mat warranty.

  8. WarmlyYours, TempZone Floor Heating System (Twin Conductor) Installation Manual

    15 watts per sq ft rolls, GFCI in the control, at least three resistance readings.

  9. WarmlyYours, TempZone Flex Roll 120V 1.5 x 24 ft, 36 sq ft, 4.5 A (TRT120-1.5x24)

    List price $519.

  10. WarmlyYours, floor heating thermostats

    nTrust 2.0 $159, nJoy WiFi $249, nSpire Touch $259, each with a built-in Class A GFCI.

  11. WarmlyYours, Bathroom Floor Heating: How Much It Costs and How to Install (2026), updated June 8, 2026

    Electrical installation $200 to $500 nationally; the 16¢ per kWh national rate; 38 sq ft heated in a 60 sq ft bathroom.

  12. U.S. Census Bureau, American Community Survey 2024 (5-year), Belleville township (via Census Reporter)

    Median year built 1951; built before 1950 and 1939 or earlier; house heating fuel; homes in two-unit buildings.

Remodeling a bathroom in Essex County? Talk it through with Andrew.

Call to talk the job through with Andrew, or send the details and Andrew will get back to you. An in-person estimate is $50, and it comes off your contract when you sign.